名词委托代购商，订货商

1. 压痕嚣,压痕物：壓痕試驗indentation test | 壓痕囂,壓痕物indentor | 壓痕硬度試驗機indentation hardness tester

2. 壓痕計：Hydraulic Saw油壓鋸台[設備] | Indentor壓痕計 | Injection Molding射出成型

3. 压痕器：压痕钢珠 indenting ball | 压痕器 indentor | 单独司轫阀 independent brake valve

4.

4. 委托代购商：委托辩护 instruction to defend | 委托代购商 indentor | 委托人 principal,entruster

1. Indentor shape was not a significant factor on failure load or failure strength.

压物的形状在负荷失败率和强度失败率中不是主要因素。

2. indentor的翻译

2. Charles E. Smith, to conduct a business in chemicals, cement, paper, milk-products, etc., as importers and indentor.

E。史密斯先生在1947年创立的，其主要业务为药品、水泥、纸张及乳制品等货物的进口与购

3. Indentor and the applied force influence the measurements such that no simple relationship exists between the measure-ments obtained with one type of durometer and those obtained with another type of durometer or other instruments used for measuring hardness.

压足的几何形状和施加力对测量的结果有影响，不同类型的硬度计和测量仪器测出的硬度值之间的不存在简单的关系。

4. In this method, drilling the double holes in the two sides of the point to be determined in welded joints, load material bridge by an indentor until it is broken, record the response between applied load and indentor displacement.

在被测材料的小区域两侧开两小孔，剪切刀具从其中一孔对被测区域的材料加载直到破坏，记录加载过程中的载荷位移曲线。

5. 1 This test method is based on the penetration of a specific type of indentor when forced into the material under specified conditions. The indentation hardness is inversely related to the penetration and is dependent on the elastic modulus and viscoelastic behavior of the material. The geometry of the

4.1本测试方法是根据有关规定，将指定类型的压足压入测试材料进行测量的，反言之，硬度与压入量有关，同时又与材料的弹性模量和粘弹性能有关。

6. indentor

6. In this method, drill the double holes in the two sides of the point to be determined in welded joints, load material bridge by an indentor until it is broken, record the response between applied load and indentor displacement. We can call this method as double holes microshear test.

在被测材料的小区域两侧开两小孔，剪切刀具从其中一孔对被测区域的材料加载直到破坏，记录加载过程中的载荷位移曲线。

7. indentor

7. Methods. An elliptical or a cloverleaf-shaped indentor covering 40% of the endplate was axially compressed against the superior endplate of 48 thoracolumbar vertebrae.

在48块胸腰椎椎体中，选用椭圆形或者四叶状的锯齿边缘的压力器，接触椎体的面积约为40％的终板面积，作轴向压迫。

8. Based on the above straight lines, the contact zone can be determined from the known indentor curvature and loading.

根据这些直线族，可以由已知的压头曲率和外载荷确定接触区尺寸。

9. The fracture toughness KIC of TiAlN coating has been measured by Weishi indenter indentor and the appearance of impress has also been observed by SEM.

并采用维氏压头测量断裂韧性KIC和通过扫描电子显微镜观察压痕形貌来评定涂层的韧性。